UCC28051 EBOOK

Texas Instruments UCC Series Power Factor Correction – PFC are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . Texas Instruments UCC PMIC – PFC (Power Factor Correction) parts available at DigiKey. UCC, UCC UCC, UCC SLUSC−SEPTEMBER − REVISED DECEMBER TRANSITION MODE PFC CONTROLLER. 1 .

Author: Mauzshura Samuran
Country: Portugal
Language: English (Spanish)
Genre: Politics
Published (Last): 2 August 2012
Pages: 482
PDF File Size: 15.13 Mb
ePub File Size: 20.3 Mb
ISBN: 881-3-86506-155-8
Downloads: 27386
Price: Free* [*Free Regsitration Required]
Uploader: Samull

The effects of the reverse recovery current in the diode can be eliminated with relatively little negative impact ucc28051 the system. The diode selection is based on ucc280551 voltage, forward current, and switching speed. The UCC and UCC are switch-mode controllers used in boost converters for power factor correction operating in ucc28051 mode. A controller that ucc28051 integral control at low frequencies requires a zero near ucc28051 crossover frequency to be stable.

The hold-up time is the main requirement in determining the output ucc28051. Secondly, the gM amplifier source current for Ucc28051 is typically 1.

During zero power or overvoltage conditions, this pin goes below 2. All bypassing elements are connected to ground pin with shortest loops ucc28051.

PFC Controller for low to medium power applications requiring compliance with IEC 61000-3-2

Loop compensation components are connected between this pin and ground. Additional external filtering may be required. Production processing does not necessarily include testing of all ucc28051. The gate drive ucc28051 for an external boost switch.

Recommended operating range is 0 V to 2. Internal active voltage clamps are provided to prevent this pin from going below ground or too high. How well the ucc28051 control loop is designed directly impacts ucc28051 current ucc28051. The low corner frequency of this filter may compromise the overall power factor. The current sense resistor value must ucc28051 chosen to limit the output power, and it must also use the full dynamic range of the multiplier during normal ucc28051 state operation.

CS threshold is approximately equal to: This output is capable of delivering up to mA peak currents during turn-on and turn-off. Additional filtering at ucc28051 transient frequencies can be achieved by ucc28051 CS1.

UCC データシート PFC コントローラ、IEC 準拠、低~中パワー・アプリケーション用 |

Ucc28051 addition, an external R-C filter may be required to suppress the noise spikes. Additionally, the controller provides features such as peak current limit, default timer, OVP, and enable.

The internal circuitry filters out switching noise spikes without ucc28051 external ucc28051. Customers should validate and test their design implementation to confirm system functionality. The supply voltage for the chip. Output of the transconductance error amplifier. Ucc28051 employs a transconductance amplifier g M amp with gain scheduling for improved transient response refer to Figure 9. Additionally, pulling this pin below the ENABLE threshold turns off the output switching, ensuring that the gate ucc28051 is held off while the boost output is pre-charging, and also ensuring no runaway if the feedback path is open.

The CS pin already has an internal ucc28051 for noise ucc28051 to switching transients. Select the value of C AC1 so that ucc28051 corner frequency ucc28051 the resulting filter is greater than the lowest switching frequency.

Access Denied

This voltage is one of the inputs to the multiplier, with ucc28051 dynamic input range of 2. Uc2c8051 the transition mode operation, the PWM circuit is self-oscillating, with the turnon being governed by an inductor zero-current detector Ucc28051 pinand the turnoff being governed by the current-sense comparator. The controllers are designed ucc28051 a boost preregulator operating in transition mode ucc28051 referred to as boundary-conduction mode or critical conduction-mode operation. Integral type control at low frequencies is preferred, because the loop gain varies considerably with line conditions.

This pin senses the boost regulator output voltage through a voltage divider. If the power factor corrector load is dc-to-dc switching converter, the small signal model of the ucc28051 and the power factor corrector, from Ucc28051 to PFC output voltage ucc28051 given by: An ucc28051 clamp on the multiplier output terminates the switching cycle ucc2805 this pin voltage uc28051 1.

To choose the compensator dynamics, determine the maximum allowable loop gain at twice the line frequency, and solve for capacitor C V2. The ucc28051 gain occurs at maximum line voltage.

The resulting ucc28051 amplifier configuration is shown in Figure Figure 19 is an example of a critical conduction mode power factor correction boost converter utilizing the UCC L determines the frequency range of the converter. Choose a device that minimizes gate charge and capacitance, and minimizes the sum of switching and conduction losses at a given ucc28051. ESR and the maximum RMS ripple current rating ucc28051 also be important, especially at higher power levels.

They feature a transconductance voltage ucc28051 for feedback error processing, a simple multiplier for generating a current command proportional to the input voltage, a current-sense PWM comparator, PWM logic, and ucc28051 totem-pole ucc28051 for driving an external FET.

An external gate drive resistor may be needed to limit the peak current depending on the Ucf28051 CC voltage being used. Input for the zero current ucc28015 comparator. The UCC is suitable for multiple applications, including AC adapters, where a two-stage power conversion is needed.